“Your walls support your home. You need to pay special attention to your house’s exterior walls because the weather out there will not be nice. It is not enough to paint your wall. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will begin peeling off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
A lot of dust and dirt is carried by air and sticks to the outer part of the wall. To ensure the efficiency of the entire process, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. Then use a power washer to clean it all off.
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop on the exterior walls over time. Follow up the cleaning process with a thorough finding of all the cracks and holes on your wall to ensure proper weatherproofing. Just fill them with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
The cement mixture seals the cracks properly. Make sure to remove all the loose cement from the wall before you apply the cement.
Step 4: Add a layer of cement waterproofing sealer
To make sure your wall is waterproof, you need to apply the cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal on the exterior walls. Allow it to dry properly.
Step 5: Pick the right water-proofer
There are many waterproof products available in the market. You have to pick the right one for the wall. Pick the water-proofer based on whether it is a concrete wall or a silicate-based one.
It is possible to choose between a silicate-based concrete sealer and a concrete waterproof coating. Pick a plaster waterproof Additive that will strengthen your walls.
Step 6: Apply the water-proofer
The water-proofer should be applied with a roller or brush. If you want to apply more than one layer, you should give a thin coat first. Let the first coat dry before adding the second one.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layers, you need to use a tar-based pitch. You should apply it on your wall.
After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your Walls.
Step 8: Consider adding gravel
The base for the trench needs to be below the footer. The drainage pipes will get adequate support from a 34-inches gravel base. Gravel provides enhanced protection and is long- lasting.
You need to lay the drainage pipe-cover and gravel. Next to the footer, level the gravel and then back-fill it. The pipe should be covered for at least 3 inches.
Step 9: Add a fabric barrier
Attach a fabric barrier to the pipe. Ensuring a fabric barrier is going to keep your system free of dirt. Then back-fill the trench and build the top of the dirt relatively high and allow it to settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia
Conclusion:
Good waterproof gives your home a new life and strength to deal with the weather issues outside. Magicrete can help you find good waterproof solutions for your walls. Magicrete has a very low and affordable price for proper weatherproofing.
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it”
